Xeltek: Difference between revisions

From Proghq
Jump to navigation Jump to search
No edit summary
 
(4 intermediate revisions by 2 users not shown)
Line 3: Line 3:
Superpro and such
Superpro and such


= 5000E =
=5000E=


== Hardware ==
==Hardware==
The 5000E is internally composed of an 8 board stack. From top to bottom, the boards are:
The 5000E is internally composed of an 8 board stack. From top to bottom, the boards are:


- GND DRV
*GND DRV
- V3 DRV
*V3 DRV
- V3 (P1-72) DRV
*V3 (P1-72) DRV
- V1 DRV
*V1 DRV
- V2 DRV
*V2 DRV
- IO BOARD
*IO BOARD
- MCU BOARD
*MCU BOARD
- POWER BOARD
*POWER BOARD


=== Voltage Pin Driver Boards ===
===Voltage Pin Driver Boards===


The V1/V2/V3* and GND drive boards share a similar topology. A set of shift registers is used to configure a transistor high or low-side drive. The GND board has two additional relays on pins, possibly for support of some high current device. The V1, V2 and V3 boards use a 74HC4094 shift reg, a ULN2003 transistor array and a high-side transistor to switch the voltage. The V2 and V3 boards incorporate a diode to prevent reverse biasing of the transistor which suggests the V1 voltage is the highest voltage used.
The V1/V2/V3* and GND drive boards share a similar topology. A set of shift registers is used to configure a transistor high or low-side drive. The GND board has two additional relays on pins, possibly for support of some high current device. The V1, V2 and V3 boards use a 74HC4094 shift reg, a ULN2003 transistor array and a high-side transistor to switch the voltage. The V2 and V3 boards incorporate a diode to prevent reverse biasing of the transistor which suggests the V1 voltage is the highest voltage used.


=== IO Board ===
===IO Board===


The IO board is just a Spartan XC2S50E FPGA connected to each IO line through a 220 ohm resistor and a diode voltage clamp. Whether the I/O voltage tracks one of the supplies (V3?) is unknown.
The IO board is just a Spartan XC2S50E FPGA connected to each IO line through a 220 ohm resistor and a diode voltage clamp. Whether the I/O voltage tracks one of the supplies (V3?) is unknown.


=== MCU Board ===
===MCU Board===


Components:
Components:


* AT91R40008 Processor (ARM7, no rom, very few peripherals, external bus interface)
*AT91R40008 Processor (ARM7, no rom, very few peripherals, external bus interface)
* TLC7226 Quad DAC  
*TLC7226 Quad DAC
* EN29LV040A Flash (512kB)
*EN29LV040A Flash (512kB)
* "Xeltek AE81" (Almost certainly an OTP FPGA)
*"Xeltek AE81" (Almost certainly an OTP FPGA)
* USB Device controller (part # unreadable in photos)
*USB Device controller (part # unreadable in photos)


=== Power Board ===
===Power Board===


* 3x LM317 + 3x MC34063 switchers
*3x LM317 + 3x MC34063 switchers
* Topology not yet reversed
*Topology not yet reversed
* Misc op amps
*Misc op amps


== Software ==
==Software==


A basic bootloader / USB loader is resident in the on-board flash. The Host software communicates with this USB loader and downloads the actual programming routines into SRAM.
A basic bootloader / USB loader is resident in the on-board flash. The Host software communicates with this USB loader and downloads the actual programming routines into SRAM.
<br />
==Socket==
<nowiki>https://www.xeltek.com/resources/technical-articles/socket-adapters/socket-adapter-selection-usage-and-maintenance/</nowiki>
<nowiki>https://www.xeltek.com/resources/technical-articles/socket-adapters/socket-adapters-en/</nowiki>
*'''DX Adapters:''' SuperPro 6100, SuperPro 6104GP
*'''EX Adapters:''' SuperPro 7000
*'''FX Adapters:''' SuperPro 7100
*'''GX Adapters:''' SuperPro 7500
*'''CX Adapters:''' SuperPro 5000, SuperPro 5004GP, SuperPro 6000, SuperPro 6000E, SuperPro 6004GP
*'''SA Adapters:''' SuperPro 610P, SuperPro 611S
Sounds like there may be some compatibility between CX and DX
https://www.vipprogrammer.com/xeltek-ex-series-adapter-socket-for-superpro-7000-programmer-2615

Latest revision as of 07:50, 10 September 2019


Superpro and such

5000E

Hardware

The 5000E is internally composed of an 8 board stack. From top to bottom, the boards are:

  • GND DRV
  • V3 DRV
  • V3 (P1-72) DRV
  • V1 DRV
  • V2 DRV
  • IO BOARD
  • MCU BOARD
  • POWER BOARD

Voltage Pin Driver Boards

The V1/V2/V3* and GND drive boards share a similar topology. A set of shift registers is used to configure a transistor high or low-side drive. The GND board has two additional relays on pins, possibly for support of some high current device. The V1, V2 and V3 boards use a 74HC4094 shift reg, a ULN2003 transistor array and a high-side transistor to switch the voltage. The V2 and V3 boards incorporate a diode to prevent reverse biasing of the transistor which suggests the V1 voltage is the highest voltage used.

IO Board

The IO board is just a Spartan XC2S50E FPGA connected to each IO line through a 220 ohm resistor and a diode voltage clamp. Whether the I/O voltage tracks one of the supplies (V3?) is unknown.

MCU Board

Components:

  • AT91R40008 Processor (ARM7, no rom, very few peripherals, external bus interface)
  • TLC7226 Quad DAC
  • EN29LV040A Flash (512kB)
  • "Xeltek AE81" (Almost certainly an OTP FPGA)
  • USB Device controller (part # unreadable in photos)

Power Board

  • 3x LM317 + 3x MC34063 switchers
  • Topology not yet reversed
  • Misc op amps

Software

A basic bootloader / USB loader is resident in the on-board flash. The Host software communicates with this USB loader and downloads the actual programming routines into SRAM.


Socket

https://www.xeltek.com/resources/technical-articles/socket-adapters/socket-adapter-selection-usage-and-maintenance/

https://www.xeltek.com/resources/technical-articles/socket-adapters/socket-adapters-en/

  • DX Adapters: SuperPro 6100, SuperPro 6104GP
  • EX Adapters: SuperPro 7000
  • FX Adapters: SuperPro 7100
  • GX Adapters: SuperPro 7500
  • CX Adapters: SuperPro 5000, SuperPro 5004GP, SuperPro 6000, SuperPro 6000E, SuperPro 6004GP
  • SA Adapters: SuperPro 610P, SuperPro 611S

Sounds like there may be some compatibility between CX and DX

https://www.vipprogrammer.com/xeltek-ex-series-adapter-socket-for-superpro-7000-programmer-2615