XGecu Protocol

From Proghq
Revision as of 15:12, 14 April 2024 by Bmx (talk | contribs) (moar fill-in)
Jump to navigation Jump to search

based on minipro, list of commands:

command TL866a/cs TL866II+ T48 T56
GET_SYSTEM_INFO 0x00 0x00 0x00 0x00
NAND_INIT - 0x02 0x02 0x02
START_TRANSACTION 0x03 0x03 0x03 0x03
END_TRANSACTION 0x04 0x04 0x04 0x04
GET_CHIP_ID 0x05 0x05 0x05 0x05
READ_USER 0x10 0x06 0x06 0x06
WRITE_USER 0x11 0x07 0x07 0x07
READ_CFG 0x12 0x08 0x08 0x08
WRITE_CFG 0x13 0x09 0x09 0x09
WRITE_USER_DATA 0x14 0x0a 0x0a 0x0a
READ_USER_DATA 0x15 0x0b 0x0b 0x0b
WRITE_CODE 0x20 0x0c 0x0c 0x0c
READ_CODE 0x21 0x0d 0x0d 0x0d
ERASE 0x22 0x0e 0x0e 0x0e
READ_DATA 0x30 0x10 0x10 0x10
WRITE_DATA 0x31 0x11 0x11 0x11
WRITE_LOCK 0x40 0x14 0x14 0x14
READ_LOCK 0x41 0x15 0x15 0x15
READ_CALIBRATION 0x42 0x16 0x16 0x16
PROTECT_OFF 0x44 0x18 0x18 0x18
PROTECT_ON 0x45 0x19 0x19 0x19
AUTODETECT 0xfc 0x37 0x37 0x37
BOOTLOADER_WRITE 0xaa 0x3b 0x3b 0x3b
BOOTLOADER_ERASE 0xcc 0x3c 0x3c 0x3c
UNLOCK_TSOP48 0xfd 0x38
GET_STATUS 0xfe 0x39 0x39 0x39
READ_JEDEC - 0x1d 0x1d 0x1d
WRITE_JEDEC - 0x1e 0x1e 0x1e
WRITE_BITSTREAM - - - 0x26
LOGIC_IC_TEST_VECTOR 0x28 0x28 0x28
WRITE_BITSTREAM2 - - - 0x2a
SWITCH - 0x3d 0x3d 0x3d
SET_LATCH 0xd1 - - -
RESET_PIN_DRIVERS 0xd0 0x2d 0x2d 0x2d
READ_ZIF_PINS 0xd2 0x35 0x35
SET_DIR 0xd4 0x34
SET_OUT 0xd5 0x36 0x36
SET_VCC_VOLTAGE 0x1b 0x1b
SET_VCC_PIN 0x2e 0x2e 0x2e
SET_VPP_VOLTAGE 0x1c 0x1c
SET_VPP_PIN 0x2f 0x2f 0x2f 0x2f
SET_GND_PIN 0x30 0x30 0x30
SET_PULLDOWNS 0x31 0x31
SET_PULLUPS 0x32 0x32
RESET 0xff 0x3f 0x3f 0x3f
? pin detect 0x3e 0x3e
?? autofind ?? 0x29
? detect_tsop_adapter 0x24
??? set / read / pin (imax?) 0x33
??? after read cfg 0x22