BPM Programmer

BP series

(11:36:56 PM) Lord_Nightmare: the main processor [of the bp1200] is an 80286-16, with a 32mhz xtal (11:37:07 PM) Lord_Nightmare: [the board labeled] std48, it would [I assume] normally have [std48] printed on it nicely (11:37:22 PM) Lord_Nightmare: this one was a refurbished unit and i guess they used an unprinted metal case for that pcb (11:37:37 PM) Lord_Nightmare: std48 is the 'relay pcb' (11:37:38 PM) digshadow: but whats the point (11:37:52 PM) Lord_Nightmare: i think it controls which pins are powered with what [rail] but am not sure (11:38:06 PM) digshadow: gotcha (11:38:07 PM) Lord_Nightmare: the bp1200 it is a 'separate' pcb on top of the unit (11:38:13 PM) digshadow: but its basically part of the unit right (11:40:54 PM) Lord_Nightmare: the bp1600 has the 'relay board' integrated as a board which sits on top of the rest of the inside of the unit inside the case (11:41:16 PM) Lord_Nightmare: i think the 1400 does as well (11:41:33 PM) Lord_Nightmare: while on the 1200 it sat on top of the unit (11:46:35 PM) Lord_Nightmare: the most basic bp unit was the bp-1148 "device programmer" (11:46:55 PM) Lord_Nightmare: note the case is identical to the 1200, and the only difference [in appearance] is 'universal' is blacked out on the wording (11:47:11 PM) Lord_Nightmare: http://vertassets.blob.core.windows.net/image/107fdcf5/107fdcf5-2dad-11d4-8c3d-009027de0829/bp1148.jpg (11:47:46 PM) Lord_Nightmare: that picture is a mockup, the std48 'layer' is missing (11:48:11 PM) Lord_Nightmare: http://thumbs.ebaystatic.com/d/l225/m/m1qMyAgqacqzlOo4KbeZLcw.jpg shows an actual 1148

BP-1200

PC interface: parallel port

Chip interface: 2 plug SM

http://atariage.com/forums/topic/142884-bp-microsystems-eprom-programmer-a-cry-for-help/

 * IF you get a TA-84 pin driver module (and a SM48D 48-pin DIP module, but  NOT the one that comes with the BP-1148) it will convert your BP-1148  to a BP1200/84.

BP-1400

PC interface: parallel port

Chip interface: 3 plug SM

BP-1400/84: [[1]]

BP-1400/240: [[2]]

Motherboard

Mezzanine board:

Power supply

BP-1410

bp-1410

External:

Power supply:

PC interface: USB

Chip interface: 3 plug SM

BP-1410/84 datasheet: [[3]]

BP-1410/240 datasheet: [[4]]

Motherboard

Motherboard USB connector:

BP-1600

External:

PC interface: parallel port

Chip interface: 3 plug SM

BP-1600 datasheet: [[5]]

1400 has a 286 and the 1410 a 486 1600 supports 1.5V parts 5000 more devices (probably a lot more by now)

Motherboard:

CPCD12A Rev. C

CPU

intel Intel DX4 iCOMP TM index=435 PC80486DX4100 L124EA01 &EW 3VOLT SL2M9 INTEL (M)(C) '89 '94

Connectors are numbered with 1 at the side of the top or left of the PCB, oriented such that writing is right side up (ie side with blue trim pot)

J10 (Fan, N/C) ^ # ^ V ^ Note ^ | 1 | N/C? | | | 2 | 16.5 | | | 3 | 0 | | | 4 | N/C? | |

J11 (Term. 1, N/C)

^ # ^ V ^ Note ^ | 1 | 0.0 | | | 2 | 1.1 | | | 3 | 0.25 | | | 4 | 5.1 | |

J12 (Term. 2, N/C)

Was this supposed to be identical to above? Broken?

^ # ^ V ^ Note ^ | 1 | 0.0 | | | 2 | 0.0 | | | 3 | 0.0 | | | 4 | 0.8 | |

Voltage header

^ Label ^ V ^ Note ^ | +5V | 5.1 | | | +3.3V | 3.3 | | | GND | 0.0 | | | -3.5V | -3.5 | | | -5V | -5.0 | | | GND | 0.0 | | | +2.5V | 2.5 | | | PGD | 4.1 | | | VTH | 1.6 | |

Power supply

J4 (12V fans...wtf?) ^ # ^ Color ^ V ^ Note ^ | 1 | Red | 35.4 | | | 2 | Red | 16.5 | | | 3 | Black | 0.0 | | | 4 | Black | 5.3 | |

J5 (to MB J4 or J20) ^ # ^ Color ^ V ^ Note ^ | 1 | Purple | 35.4 | | | 2 | Orange | 16.5 | | | 3 | Black | 0.0 | | | 4 | Red | 5.3 | |

J6 (to MB J4 or J20) ^ # ^ Color ^ V ^ Note ^ | 1 | Purple | 35.4 | | | 2 | Orange | 16.5 | | | 3 | Black | 0.0 | | | 4 | Red | 5.3 | |

BP-2200

"Concurrent Programming System"

PC interface: parallel port

Chip interface: 4X 3 plug SM

BP-2200 datasheet: [[6]]

Parallel to USB upgrade

Main page: bpm:WWAVUSBEPP

USB hub

Used on gang programmers

EP-1

PC interface: parallel port

Chip interface: DIP

EP-1132

PC interface: parallel port

Chip interface: DIP-

EP-1140

PC interface: parallel port

Chip interface: DIP-40

PLD-1128

PC interface: parallel port

Chip interface: DIP-28

CP-1128

PC interface: parallel port

Chip interface: DIP-28

Silicon Sculptor

Actel programmers made by BPM.

As these cost less than the "real" BPM programmers, presumably can't be used with normal BPM software and/or work with other adapters

Silicon Sculptor 1

Has 2 headers (left/right) that adaptors plug into

Interface: parallel port

There is version with 1 connector and a version with 6 connectors

1X markings

Silicon Sculptor FAIL ACTIVE PASS START ACTEL DEVICE PROGRAMMER BP MICROSYSTEMS

Silicon Sculptor 2

Markings:

Silicon Sculptor II Actel FAIL ACTIVE PASS ACTEL DEVICE PROGRAMMER BP MICROSYSTEMS

Actel Silicon Sculptor 3

Above: DO NOT TOUCH!

This appears to be a crippled BP-1410 (however, it has the front-panel button and the 512MB of RAM present in the BP-1710). No analysis has been done to figure out where the devices differ (firmware, FPGA, host, etc)

Product page: [[7]]

I love how they switched from roman numerals to Arabic numbers. Maybe they'll call the next one Silicon Sculptor D…

Has 3 headers (left/right/top) that adaptors plug into

Interface: USB

Markings:

Silicon Sculptor 3 Actel FAIL ACTIVE PASS START (button) ACTEL DEVICE PROGRAMMER BP MICROSYSTEMS

\\

Motherboard

Main assembly:

Driver board: