Difference between revisions of "BPM Programmer"
| Line 1: | Line 1: | ||
| − | [[ | + | [[Category_BPM]] |
| − | [[ | + | [[Category_Programmer]] |
| − | [[ | + | [[Category_Hardware]] |
= BP series = | = BP series = | ||
| Line 52: | Line 52: | ||
|} | |} | ||
| − | + | (11:36:56 PM) Lord_Nightmare: the main processor [of the bp1200] is an 80286-16, with a 32mhz xtal | |
| − | (11:36:56 PM) Lord_Nightmare: the main processor [of the bp1200] is an 80286-16, with a 32mhz xtal | + | (11:37:07 PM) Lord_Nightmare: [the board labeled] std48, it would [I assume] normally have [std48] printed on it nicely |
| − | (11:37:07 PM) Lord_Nightmare: [the board labeled] std48, it would [I assume] normally have [std48] printed on it nicely | + | (11:37:22 PM) Lord_Nightmare: this one was a refurbished unit and i guess they used an unprinted metal case for that pcb |
| − | (11:37:22 PM) Lord_Nightmare: this one was a refurbished unit and i guess they used an unprinted metal case for that pcb | + | (11:37:37 PM) Lord_Nightmare: std48 is the 'relay pcb' |
| − | (11:37:37 PM) Lord_Nightmare: std48 is the 'relay pcb' | + | (11:37:38 PM) digshadow: but whats the point |
| − | (11:37:38 PM) digshadow: but whats the point | + | (11:37:52 PM) Lord_Nightmare: i think it controls which pins are powered with what [rail] but am not sure |
| − | (11:37:52 PM) Lord_Nightmare: i think it controls which pins are powered with what [rail] but am not sure | + | (11:38:06 PM) digshadow: gotcha |
| − | (11:38:06 PM) digshadow: gotcha | + | (11:38:07 PM) Lord_Nightmare: the bp1200 it is a 'separate' pcb on top of the unit |
| − | (11:38:07 PM) Lord_Nightmare: the bp1200 it is a 'separate' pcb on top of the unit | + | (11:38:13 PM) digshadow: but its basically part of the unit right |
| − | (11:38:13 PM) digshadow: but its basically part of the unit right | + | (11:40:54 PM) Lord_Nightmare: the bp1600 has the 'relay board' integrated as a board which sits on top of the rest of the inside of the unit inside the case |
| − | (11:40:54 PM) Lord_Nightmare: the bp1600 has the 'relay board' integrated as a board which sits on top of the rest of the inside of the unit inside the case | + | (11:41:16 PM) Lord_Nightmare: i think the 1400 does as well |
| − | (11:41:16 PM) Lord_Nightmare: i think the 1400 does as well | + | (11:41:33 PM) Lord_Nightmare: while on the 1200 it sat on top of the unit |
| − | (11:41:33 PM) Lord_Nightmare: while on the 1200 it sat on top of the unit | + | (11:46:35 PM) Lord_Nightmare: the most basic bp unit was the bp-1148 "device programmer" |
| − | (11:46:35 PM) Lord_Nightmare: the most basic bp unit was the bp-1148 "device programmer" | + | (11:46:55 PM) Lord_Nightmare: note the case is identical to the 1200, and the only difference [in appearance] is 'universal' is blacked out on the wording |
| − | (11:46:55 PM) Lord_Nightmare: note the case is identical to the 1200, and the only difference [in appearance] is 'universal' is blacked out on the wording | + | (11:47:11 PM) Lord_Nightmare: http://vertassets.blob.core.windows.net/image/107fdcf5/107fdcf5-2dad-11d4-8c3d-009027de0829/bp1148.jpg |
| − | (11:47:11 PM) Lord_Nightmare: http: | + | (11:47:46 PM) Lord_Nightmare: that picture is a mockup, the std48 'layer' is missing |
| − | (11:47:46 PM) Lord_Nightmare: that picture is a mockup, the std48 'layer' is missing | + | (11:48:11 PM) Lord_Nightmare: http://thumbs.ebaystatic.com/d/l225/m/m1qMyAgqacqzlOo4KbeZLcw.jpg shows an actual 1148 |
| − | (11:48:11 PM) Lord_Nightmare: http: | ||
| − | |||
| Line 97: | Line 95: | ||
Chip interface: 2 plug SM | Chip interface: 2 plug SM | ||
| − | http: | + | http://atariage.com/forums/topic/142884-bp-microsystems-eprom-programmer-a-cry-for-help/ |
* IF you get a TA-84 pin driver module (and a SM48D 48-pin DIP module, but NOT the one that comes with the BP-1148) it will convert your BP-1148 to a BP1200/84. | * IF you get a TA-84 pin driver module (and a SM48D 48-pin DIP module, but NOT the one that comes with the BP-1148) it will convert your BP-1148 to a BP1200/84. | ||
| Line 106: | Line 104: | ||
Chip interface: 3 plug SM | Chip interface: 3 plug SM | ||
| − | BP-1400/84: | + | BP-1400/84: [http://web.archive.org/web/20061119190006/http://www.bpmicro.com/products.nsf/7df54a7a9b18958d862566710079b2a0/cd8e1e770bf83c0e862569510070a6cf/$FILE/1400-84%20Data%20Sheet.pdf] |
| − | BP-1400/240: | + | BP-1400/240: [http://web.archive.org/web/20061119190026/http://www.bpmicro.com/products.nsf/7df54a7a9b18958d862566710079b2a0/cd8e1e770bf83c0e862569510070a6cf/$FILE/1400-240%20Data%20Sheet.pdf] |
=== Motherboard === | === Motherboard === | ||
| Line 146: | Line 144: | ||
Chip interface: 3 plug SM | Chip interface: 3 plug SM | ||
| − | BP-1410/84 datasheet: | + | BP-1410/84 datasheet: [http://web.archive.org/web/20060321214044/http://www.bpmicro.com/web/bphome.nsf/webpages/141084-PDF/$FILE/1410_84.pdf] |
| − | BP-1410/240 datasheet: | + | BP-1410/240 datasheet: [http://web.archive.org/web/20060321214333/http://www.bpmicro.com/web/bphome.nsf/webpages/1410240-PDF/$FILE/1410_240.pdf] |
=== Motherboard === | === Motherboard === | ||
| Line 175: | Line 173: | ||
Chip interface: 3 plug SM | Chip interface: 3 plug SM | ||
| − | BP-1600 datasheet: | + | BP-1600 datasheet: [http://web.archive.org/web/20050530023158/http://www.bpmicro.com/web/BPhome.nsf/webpages/1600-PDF/$FILE/1600DS_EN_0703.pdf] |
| − | + | 1400 has a 286 and the 1410 a 486 | |
| − | 1400 has a 286 and the 1410 a 486 | + | 1600 supports 1.5V parts |
| − | 1600 supports 1.5V parts | + | 5000 more devices (probably a lot more by now) |
| − | 5000 more devices (probably a lot more by now) | ||
| − | |||
=== Motherboard: === | === Motherboard: === | ||
| Line 193: | Line 189: | ||
CPU | CPU | ||
| − | + | intel | |
| − | intel | + | Intel DX4 |
| − | Intel DX4 | + | iCOMP TM index=435 |
| − | iCOMP TM index=435 | + | PC80486DX4100 |
| − | PC80486DX4100 | + | L124EA01 |
| − | L124EA01 | + | &EW 3VOLT SL2M9 |
| − | &EW 3VOLT SL2M9 | + | INTEL (M)(C) '89 '94 |
| − | INTEL (M)(C) '89 '94 | ||
| − | |||
Connectors are numbered with 1 at the side of the top or left of the PCB, oriented such that writing is right side up (ie side with blue trim pot) | Connectors are numbered with 1 at the side of the top or left of the PCB, oriented such that writing is right side up (ie side with blue trim pot) | ||
| Line 334: | Line 328: | ||
Chip interface: 4X 3 plug SM | Chip interface: 4X 3 plug SM | ||
| − | BP-2200 datasheet: | + | BP-2200 datasheet: [http://web.archive.org/web/20061119185923/http://www.bpmicro.com/products.nsf/7df54a7a9b18958d862566710079b2a0/bc7af9c2aab5d676862566540077413c/$FILE/2200%20Data%20Sheet.pdf] |
== Parallel to USB upgrade == | == Parallel to USB upgrade == | ||
| − | Main page: [[ | + | Main page: [[bpm_WWAVUSBEPP]] |
| Line 404: | Line 398: | ||
1X markings | 1X markings | ||
| − | + | Silicon Sculptor | |
| − | Silicon Sculptor | + | FAIL |
| − | FAIL | + | ACTIVE |
| − | ACTIVE | + | PASS |
| − | PASS | + | START |
| − | START | + | ACTEL DEVICE PROGRAMMER |
| − | ACTEL DEVICE PROGRAMMER | + | BP MICROSYSTEMS |
| − | BP MICROSYSTEMS | ||
| − | |||
== Silicon Sculptor 2 == | == Silicon Sculptor 2 == | ||
| Line 418: | Line 410: | ||
Markings: | Markings: | ||
| − | + | Silicon Sculptor II | |
| − | Silicon Sculptor II | + | Actel |
| − | Actel | + | FAIL |
| − | FAIL | + | ACTIVE |
| − | ACTIVE | + | PASS |
| − | PASS | + | ACTEL DEVICE PROGRAMMER |
| − | ACTEL DEVICE PROGRAMMER | + | BP MICROSYSTEMS |
| − | BP MICROSYSTEMS | ||
| − | |||
[[File:anon_bpm_ss2_ext.jpg|frameless]] | [[File:anon_bpm_ss2_ext.jpg|frameless]] | ||
| Line 463: | Line 453: | ||
This appears to be a crippled BP-1410 (however, it has the front-panel button and the 512MB of RAM present in the BP-1710). No analysis has been done to figure out where the devices differ (firmware, FPGA, host, etc) | This appears to be a crippled BP-1410 (however, it has the front-panel button and the 512MB of RAM present in the BP-1710). No analysis has been done to figure out where the devices differ (firmware, FPGA, host, etc) | ||
| − | Product page: | + | Product page: [http://www.microsemi.com/products/fpga-soc/design-resources/programming/silicon-sculptor-3] |
I love how they switched from roman numerals to Arabic numbers. Maybe they'll call the next one Silicon Sculptor D… | I love how they switched from roman numerals to Arabic numbers. Maybe they'll call the next one Silicon Sculptor D… | ||
| Line 473: | Line 463: | ||
Markings: | Markings: | ||
| − | + | Silicon Sculptor 3 | |
| − | Silicon Sculptor 3 | + | Actel |
| − | Actel | + | FAIL |
| − | FAIL | + | ACTIVE |
| − | ACTIVE | + | PASS |
| − | PASS | + | START (button) |
| − | START (button) | + | ACTEL DEVICE PROGRAMMER |
| − | ACTEL DEVICE PROGRAMMER | + | BP MICROSYSTEMS |
| − | BP MICROSYSTEMS | + | |
| − | |||
| − | |||
=== External === | === External === | ||
Revision as of 02:19, 5 July 2019
Category_BPM Category_Programmer Category_Hardware
BP series
| Models | Motherboard
silkscreen |
Motherboard
CPU |
Motherboard
FPGA sticker |
Tech adapter
silkscreen |
Which | Accessory | Note |
|---|---|---|---|---|---|---|---|
| Actel SS2 | CPCB12A Rev. C | U5
W42MX24A BP MICROSYSTEMS 09/20/02 |
CPCBVLTA REV. B | mcmaster | Button | ||
| BPM 1410 | CPCBD03223 Rev. F | N/A | 2002 BP MICROSYSTEMS | mcmaster | |||
| BPM 1600 | CPCB12A Rev. C | (handwritten)
MUS 28781 |
CPCBVLTA | REV. | B |
(11:36:56 PM) Lord_Nightmare: the main processor [of the bp1200] is an 80286-16, with a 32mhz xtal (11:37:07 PM) Lord_Nightmare: [the board labeled] std48, it would [I assume] normally have [std48] printed on it nicely (11:37:22 PM) Lord_Nightmare: this one was a refurbished unit and i guess they used an unprinted metal case for that pcb (11:37:37 PM) Lord_Nightmare: std48 is the 'relay pcb' (11:37:38 PM) digshadow: but whats the point (11:37:52 PM) Lord_Nightmare: i think it controls which pins are powered with what [rail] but am not sure (11:38:06 PM) digshadow: gotcha (11:38:07 PM) Lord_Nightmare: the bp1200 it is a 'separate' pcb on top of the unit (11:38:13 PM) digshadow: but its basically part of the unit right (11:40:54 PM) Lord_Nightmare: the bp1600 has the 'relay board' integrated as a board which sits on top of the rest of the inside of the unit inside the case (11:41:16 PM) Lord_Nightmare: i think the 1400 does as well (11:41:33 PM) Lord_Nightmare: while on the 1200 it sat on top of the unit (11:46:35 PM) Lord_Nightmare: the most basic bp unit was the bp-1148 "device programmer" (11:46:55 PM) Lord_Nightmare: note the case is identical to the 1200, and the only difference [in appearance] is 'universal' is blacked out on the wording (11:47:11 PM) Lord_Nightmare: http://vertassets.blob.core.windows.net/image/107fdcf5/107fdcf5-2dad-11d4-8c3d-009027de0829/bp1148.jpg (11:47:46 PM) Lord_Nightmare: that picture is a mockup, the std48 'layer' is missing (11:48:11 PM) Lord_Nightmare: http://thumbs.ebaystatic.com/d/l225/m/m1qMyAgqacqzlOo4KbeZLcw.jpg shows an actual 1148
BP-1200
PC interface: parallel port
Chip interface: 2 plug SM
http://atariage.com/forums/topic/142884-bp-microsystems-eprom-programmer-a-cry-for-help/
- IF you get a TA-84 pin driver module (and a SM48D 48-pin DIP module, but NOT the one that comes with the BP-1148) it will convert your BP-1148 to a BP1200/84.
BP-1400
PC interface: parallel port
Chip interface: 3 plug SM
BP-1400/84: [1]
BP-1400/240: [2]
Motherboard
Mezzanine board:
Power supply
BP-1410
External:
Power supply:
PC interface: USB
Chip interface: 3 plug SM
BP-1410/84 datasheet: [3]
BP-1410/240 datasheet: [4]
Motherboard
Motherboard USB connector:
BP-1600
External:
PC interface: parallel port
Chip interface: 3 plug SM
BP-1600 datasheet: [5]
1400 has a 286 and the 1410 a 486 1600 supports 1.5V parts 5000 more devices (probably a lot more by now)
Motherboard:
CPCD12A Rev. C
CPU
intel Intel DX4 iCOMP TM index=435 PC80486DX4100 L124EA01 &EW 3VOLT SL2M9 INTEL (M)(C) '89 '94
Connectors are numbered with 1 at the side of the top or left of the PCB, oriented such that writing is right side up (ie side with blue trim pot)
J10 (Fan, N/C)
| # | V | Note |
|---|---|---|
| 1 | N/C? | |
| 2 | 16.5 | |
| 3 | 0 | |
| 4 | N/C? |
J11 (Term. 1, N/C)
| # | V | Note |
|---|---|---|
| 1 | 0.0 | |
| 2 | 1.1 | |
| 3 | 0.25 | |
| 4 | 5.1 |
J12 (Term. 2, N/C)
Was this supposed to be identical to above? Broken?
| # | V | Note |
|---|---|---|
| 1 | 0.0 | |
| 2 | 0.0 | |
| 3 | 0.0 | |
| 4 | 0.8 |
Voltage header
| Label | V | Note |
|---|---|---|
| +5V | 5.1 | |
| +3.3V | 3.3 | |
| GND | 0.0 | |
| -3.5V | -3.5 | |
| -5V | -5.0 | |
| GND | 0.0 | |
| +2.5V | 2.5 | |
| PGD | 4.1 | |
| VTH | 1.6 |
Power supply
J4 (12V fans...wtf?)
| # | Color | V | Note |
|---|---|---|---|
| 1 | Red | 35.4 | |
| 2 | Red | 16.5 | |
| 3 | Black | 0.0 | |
| 4 | Black | 5.3 |
J5 (to MB J4 or J20)
| # | Color | V | Note |
|---|---|---|---|
| 1 | Purple | 35.4 | |
| 2 | Orange | 16.5 | |
| 3 | Black | 0.0 | |
| 4 | Red | 5.3 |
J6 (to MB J4 or J20)
| # | Color | V | Note |
|---|---|---|---|
| 1 | Purple | 35.4 | |
| 2 | Orange | 16.5 | |
| 3 | Black | 0.0 | |
| 4 | Red | 5.3 |
BP-2200
"Concurrent Programming System"
PC interface: parallel port
Chip interface: 4X 3 plug SM
BP-2200 datasheet: [6]
Parallel to USB upgrade
Main page: bpm_WWAVUSBEPP
USB hub
Used on gang programmers
EP series
EP-1
PC interface: parallel port
Chip interface: DIP
EP-1132
PC interface: parallel port
Chip interface: DIP-
EP-1140
PC interface: parallel port
Chip interface: DIP-40
PLD series
PLD-1128
PC interface: parallel port
Chip interface: DIP-28
CP series
CP-1128
PC interface: parallel port
Chip interface: DIP-28
Silicon Sculptor
Actel programmers made by BPM.
As these cost less than the "real" BPM programmers, presumably can't be used with normal BPM software and/or work with other adapters
Silicon Sculptor 1
Has 2 headers (left/right) that adaptors plug into
Interface: parallel port
There is version with 1 connector and a version with 6 connectors
1X markings
Silicon Sculptor FAIL ACTIVE PASS START ACTEL DEVICE PROGRAMMER BP MICROSYSTEMS
Silicon Sculptor 2
Markings:
Silicon Sculptor II Actel FAIL ACTIVE PASS ACTEL DEVICE PROGRAMMER BP MICROSYSTEMS
mcmaster notes
2018-09-12
- Open SS2
- Think this was the eBay unit?
- PCB is identical to one used in BP-1600
- Both have blue bodge wire
- SS2 has RAM installed
Actel Silicon Sculptor 3
Above: DO NOT TOUCH!
This appears to be a crippled BP-1410 (however, it has the front-panel button and the 512MB of RAM present in the BP-1710). No analysis has been done to figure out where the devices differ (firmware, FPGA, host, etc)
Product page: [7]
I love how they switched from roman numerals to Arabic numbers. Maybe they'll call the next one Silicon Sculptor D…
Has 3 headers (left/right/top) that adaptors plug into
Interface: USB
Markings:
Silicon Sculptor 3 Actel FAIL ACTIVE PASS START (button) ACTEL DEVICE PROGRAMMER BP MICROSYSTEMS
External
Motherboard
Main assembly:
Driver board:
Power supply
