XGecu Protocol: Difference between revisions
Jump to navigation
Jump to search
m (moar fill-in) |
m (no x24 for T56) |
||
Line 290: | Line 290: | ||
| | | | ||
|- | |- | ||
| | |detect_drm_adapter | ||
| | | | ||
| | | | ||
|0x24 | |0x24 | ||
| | | - | ||
|- | |- | ||
|??? set / read / pin (imax?) | |??? set / read / pin (imax?) |
Revision as of 15:20, 16 April 2024
based on minipro, list of commands:
command | TL866a/cs | TL866II+ | T48 | T56 |
GET_SYSTEM_INFO | 0x00 | 0x00 | 0x00 | 0x00 |
NAND_INIT | - | 0x02 | 0x02 | 0x02 |
START_TRANSACTION | 0x03 | 0x03 | 0x03 | 0x03 |
END_TRANSACTION | 0x04 | 0x04 | 0x04 | 0x04 |
GET_CHIP_ID | 0x05 | 0x05 | 0x05 | 0x05 |
READ_USER | 0x10 | 0x06 | 0x06 | 0x06 |
WRITE_USER | 0x11 | 0x07 | 0x07 | 0x07 |
READ_CFG | 0x12 | 0x08 | 0x08 | 0x08 |
WRITE_CFG | 0x13 | 0x09 | 0x09 | 0x09 |
WRITE_USER_DATA | 0x14 | 0x0a | 0x0a | 0x0a |
READ_USER_DATA | 0x15 | 0x0b | 0x0b | 0x0b |
WRITE_CODE | 0x20 | 0x0c | 0x0c | 0x0c |
READ_CODE | 0x21 | 0x0d | 0x0d | 0x0d |
ERASE | 0x22 | 0x0e | 0x0e | 0x0e |
READ_DATA | 0x30 | 0x10 | 0x10 | 0x10 |
WRITE_DATA | 0x31 | 0x11 | 0x11 | 0x11 |
WRITE_LOCK | 0x40 | 0x14 | 0x14 | 0x14 |
READ_LOCK | 0x41 | 0x15 | 0x15 | 0x15 |
READ_CALIBRATION | 0x42 | 0x16 | 0x16 | 0x16 |
PROTECT_OFF | 0x44 | 0x18 | 0x18 | 0x18 |
PROTECT_ON | 0x45 | 0x19 | 0x19 | 0x19 |
AUTODETECT | 0xfc | 0x37 | 0x37 | 0x37 |
BOOTLOADER_WRITE | 0xaa | 0x3b | 0x3b | 0x3b |
BOOTLOADER_ERASE | 0xcc | 0x3c | 0x3c | 0x3c |
UNLOCK_TSOP48 | 0xfd | 0x38 | ||
GET_STATUS | 0xfe | 0x39 | 0x39 | 0x39 |
READ_JEDEC | - | 0x1d | 0x1d | 0x1d |
WRITE_JEDEC | - | 0x1e | 0x1e | 0x1e |
WRITE_BITSTREAM | - | - | - | 0x26 |
LOGIC_IC_TEST_VECTOR | 0x28 | 0x28 | 0x28 | |
WRITE_BITSTREAM2 | - | - | - | 0x2a |
SWITCH | - | 0x3d | 0x3d | 0x3d |
SET_LATCH | 0xd1 | - | - | - |
RESET_PIN_DRIVERS | 0xd0 | 0x2d | 0x2d | 0x2d |
READ_ZIF_PINS | 0xd2 | 0x35 | 0x35 | |
SET_DIR | 0xd4 | 0x34 | ||
SET_OUT | 0xd5 | 0x36 | 0x36 | |
SET_VCC_VOLTAGE | 0x1b | 0x1b | ||
SET_VCC_PIN | 0x2e | 0x2e | 0x2e | |
SET_VPP_VOLTAGE | 0x1c | 0x1c | ||
SET_VPP_PIN | 0x2f | 0x2f | 0x2f | 0x2f |
SET_GND_PIN | 0x30 | 0x30 | 0x30 | |
SET_PULLDOWNS | 0x31 | 0x31 | ||
SET_PULLUPS | 0x32 | 0x32 | ||
RESET | 0xff | 0x3f | 0x3f | 0x3f |
? pin detect | 0x3e | 0x3e | ||
?? autofind ?? | 0x29 | |||
detect_drm_adapter | 0x24 | - | ||
??? set / read / pin (imax?) | 0x33 | |||
??? after read cfg | 0x22 |