T48: Difference between revisions
No edit summary |
No edit summary |
||
| (3 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
[[Category:Hardware]] | |||
[[Category:Programmer]] | |||
==WCH-link== | |||
Debug header | Debug header | ||
| Line 13: | Line 16: | ||
#ground | #ground | ||
#BOOT | #BOOT | ||
#*U5 pin 4 | #*Drives SM16306SJ (shift register) latch enable (LE) Z to prevent bus contention with programmer | ||
#*SM16306SJ | #**SR output is shared with one of the WCH-Link pins (SWDCLK/SWDIO, forget which) | ||
#**U5 pin 4 | |||
#*4 => LE | #**SM16306SJ - serial to parallel shift register / LED driver? Datasheet: [https://datasheet.lcsc.com/lcsc/2105241639_Shenzhen-Sunmoon-Micro-SM16306S_C2830324.pdf] Product page: [https://www.lcsc.com/product-detail/LED-Drivers_Shenzhen-Sunmoon-Micro-SM16306S_C2830324.html] | ||
#*BOOT1 | #**4 => LE | ||
#**BOOT1 ??? | |||
#* | |||
| Line 28: | Line 33: | ||
WCHISPStudio/WCHISPTool (the separate programming tool, accessible via Tools->WCH In-System Programmer in the IDE) sees the device when jumpered this way. The IDE doesn't, so it might be necessary to use this tool to do the programming. | WCHISPStudio/WCHISPTool (the separate programming tool, accessible via Tools->WCH In-System Programmer in the IDE) sees the device when jumpered this way. The IDE doesn't, so it might be necessary to use this tool to do the programming. | ||
===Unbrick | |||
== Dev flow == | |||
https://github.com/davidcarne/t48-dummy-c-program | |||
Sample flow for Linux doing LED blink | |||
==Unbrick== | |||
In theory we have all firmware (system ROM, bootloader, main firmware) and should be able to unbrick devices. However, I was unable to restore my devices | In theory we have all firmware (system ROM, bootloader, main firmware) and should be able to unbrick devices. However, I was unable to restore my devices | ||
Latest revision as of 07:46, 16 April 2024
WCH-link
Debug header
- BO
- 94 BOOT0
- 3V3
- no 3.3V on PCB. I guess connect to WCH-Link 3V3?
- SWDCLK
- PA14/SWCLK
- SWDIO
- PA13/SWDIO
- ground
- BOOT
boot to high pin => seems to enable USB even with SWD plugged in
ID 4348:55e0 WinChipHead
This is USB bootloader mode
Document at https://raw.githubusercontent.com/openwch/ch32v307/main/EVT/PUB/CH32V30xEVT%20Evaluation%20Board%20Manual.pdf indicates that for USB bootloader mode: "(1) BOOT0 to VCC, BOOT1 to the ground, connect to PC via serial port or USB"
WCHISPStudio/WCHISPTool (the separate programming tool, accessible via Tools->WCH In-System Programmer in the IDE) sees the device when jumpered this way. The IDE doesn't, so it might be necessary to use this tool to do the programming.
Dev flow
https://github.com/davidcarne/t48-dummy-c-program
Sample flow for Linux doing LED blink
Unbrick
In theory we have all firmware (system ROM, bootloader, main firmware) and should be able to unbrick devices. However, I was unable to restore my devices
Theory: unrick issue is firmware is not at correct .hex location. Things that didn't seem to work to get firmware .hex file:
objcopy --input-target=binary --output-target=ihex --set-start 0x08000000 t48_bootrom_2022-06-30.bin t48_bootrom_2022-06-30.hex
objcopy --input-target=binary --output-target=ihex --change-addresses 0x08000000 t48_bootrom_2022-06-30.bin t48_bootrom_2022-06-30.hex
objcopy --input-target=binary --output-target=ihex t48_bootrom_2022-06-30.bin temp.hex objcopy --change-addresses 0x08000000 temp.hex t48_bootrom_2022-06-30.hex